|
| Author |
Message |
Borrego
Member
|
# Posted: 16 Apr 2017 22:18
Reply
I'm building a 12' x 10' tool shed/workshop (at my 'full-time' house) and I know someone here has got to have some crazy, trick concepts about how to organize them. I am a working contractor as well so any ways to get rid of my typical disorganized workshops would be welcome......Pics or drawings if possible
Thanks guys and gals...!
|
|
Gary O
Member
|
# Posted: 17 Apr 2017 07:30 - Edited by: Gary O
Reply
That’s pretty tiny for a shop, Borrego.
I only say that because I had one that size for a long time.
But
It can work, even if you have a table saw and maybe sliding miter or radial arm saw.
If you have those, you’ll want doors on both ends, wide doors, for sheet stock and ripping lumber.
Heck, I need doors on both ends for my (12 x 16) shop now.
Anyway, you’ll want a work bench all the way down on one side and standing storage on the other.
Ideal headroom would be at least eight feet from floor to rafter.
And those rafters will need to have enough space above for storing lumber.
So, the doors need to be high enough to slide that lumber in from outside.
And opening out.
I suggest not using pegboard, and having walls stout enough for finish nails to hang hand tools where they’re handy.
These are just suggestions, of course, from a guy…
who has had…..
a 10 x 12 shop…..
Always fun to see what you build, as for quite a few years now, you've showed your abilities and unique desert structures right here on SCF.
Here’s a crude overhead drawing to clear up what I may have not conveyed via word.
Of course nothing is to scale…probably.
Happy building, pard.
|
|
Steve_S
Member
|
# Posted: 17 Apr 2017 09:22
Reply
Drawer / Container clearly labelled as "Safe Place #1" where things get put when in a hurry or if it's new & has no allocated place. Temp Storage for important items that should never be lost. Safe Place #1 is permanent & fixed (be it on a shelf or cabinet etc) so it always exists and is always at hand... Safe Place's #2, #3 can be portable BUT easily identified at a glance...
One of my favourite organizers is the Folger's Coffee containers... Nails, Screws etc can be organized and stored plus handy with the grab handle... Always have empty ones handy, boy they are useful for a lot of things !
|
|
Borrego
Member
|
# Posted: 17 Apr 2017 10:00 - Edited by: Borrego
Reply
Thanks fellas, good ideas. I am going to make this baby 10' tall to have storage....with a flat shed roof.....
|
|
Gary O
Member
|
# Posted: 17 Apr 2017 13:43 - Edited by: Gary O
Reply
Quoting: Steve_S One of my favourite organizers is the Folger's Coffee containers... Nails, Screws etc can be organized and stored plus handy with the grab handle... Always have empty ones handy, boy they are useful for a lot of things !
I used to like those racks of 1000 little see thru plastic drawers.
Until I tired of pulling 1000 little see thru drawers that I couldn’t actually see thru, to find who knows what by now.
Yeah, coffee cans
And
Tuna cans
All in a thin pull out drawer under the work bench
Immediate vision of everything small
|
|
DaveBell
Moderator
|
# Posted: 17 Apr 2017 14:09
Reply
Holes drilled into studs for rebar or conduit to hang shovels and rakes upside down. Gets them off the floor.
|
|
Borrego
Member
|
# Posted: 17 Apr 2017 20:57
Reply
Quoting: DaveBell Holes drilled into studs for rebar or conduit to hang shovels and rakes upside down. Gets them off the floor.
^^^
Me like...
|
|
Borrego
Member
|
# Posted: 17 Apr 2017 21:04
Reply
Quoting: Gary O Until I tired of pulling 1000 little see thru drawers that I couldn’t actually see thru, to find who knows what by now.
hahahaha... I thought that was just me..and then I would painstakingly make little labels for them figuring that would solve the problem..Not.
|
|
|
DaveBell
Moderator
|
# Posted: 17 Apr 2017 21:26 - Edited by: DaveBell
Reply
That idea was from woodworking for storing wood. Ya know better yet, since studs are 16 OC, (might take modifying width since shovels are like 6-10 inches wide, how about hanging from the ceiling joists with eye hooks and coat hanger wire, two runs of 3/4 conduit spaced about 4-5 inches apart. Take the shovel, rake, etc. sideways between the bars, twist and they hang. Push then all back against the wall like a coat rack. Spread them out to remove one. So maybe one 8 foot 3/4 conduit cut in half. The coat hanger wire needs to be secured to the conduit very well. You could put conduit 90 degree connectors on the ends with 4 inch conduit between to make a rectangle that keeps its shape.
|
|
old243
Member
|
# Posted: 18 Apr 2017 09:15
Reply
I use 10 liter plastic rectangular water, spray, oil, jugs. Lay on their side and cut most of the top out. I have one for each of my machines. Keep all the parts for each in one place. label the front. I keep them on a high shelf , out of the road, until I need something. Could you extend one or both roof sides out several feet, to give storage or cabinets on the outside, you have a 10 foot eve.Good luck with your new shop. old243
|
|
skootamattaschmidty
Member
|
# Posted: 18 Apr 2017 15:47
Reply
I'm not sure if you are on pintrest or not but there are some amazing ideas and projects on there for storage and tool organization. Might be worth a look.
|
|
Borrego
Member
|
# Posted: 18 Apr 2017 19:08
Reply
Thought I'd share what I find as I go along..
Just found this, pretty cool..
http://makezine.com/2015/05/05/reorganize-workshop-custom-made-tool-holders/
|
|
Borrego
Member
|
# Posted: 18 Apr 2017 19:12
Reply
Maybe I'll do something like this, with an outdoor opening window/bench...to get more room and I love working outdoors anyway...?
|
|
Borrego
Member
|
# Posted: 18 Apr 2017 19:41
Reply
Quoting: skootamattaschmidty I'm not sure if you are on pintrest or not
Oh yeah, great ideas there!
|
|
paulz
Member
|
# Posted: 18 Apr 2017 21:00
Reply
When you run out of room on the bench and in drawers, attach storage jars to the ceiling or bottom of shelves by their screw on lids.
|
|
Jim in NB
Member
|
# Posted: 19 Apr 2017 06:43
Reply
Used to use coffee cans but after years am changing over to glass containers - much easier to see and grab as your vision slowly goes.
|
|
Gary O
Member
|
# Posted: 19 Apr 2017 09:01
Reply
Quoting: Borrego Thought I'd share what I find as I go along..Just found this, pretty cool..http://makezine.com/2015/05/05/reorganize-workshop-custom-made-tool-holders/
I…I…I think I just had an organizationasm
I’d never get anything done
...wouldn’t wanna mess up the feng shui
|
|
Gary O
Member
|
# Posted: 19 Apr 2017 09:33
Reply
Quoting: Jim in NB Used to use coffee cans but after years am changing over to glass containers - much easier to see and grab as your vision slowly goes.
Y’know, I inherited a rack of baby food jars with their lids screwed to boards.
The ol’ guy, my step grandad, had carefully organized his shop, something to behold.
Anyway, after putting all my screws, nuts, washers (flat, lock, star) and all the other tiny stuff I had, into those jars, I discovered screwing those lids back on were a bit tricky.
Then I discovered picking up those screws, nuts, washers (flat, lock, star) and all the other tiny stuff off the floor was something I really wasn’t all that fond of.
So
I poured everthing into coffee cans.
When I need a certain screw or washer, I empty a coffee can onto a cookie sheet, or even the work bench, pick out what I want, and scrape everthing back into the coffee can.
And
Whenever I end up with the odd stuff after a project, just toss it into the can.
So,
I now spend my new found extra time on sites, helping people
Lines are open
|
|
Jim in NB
Member
|
# Posted: 9 Apr 2019 08:31
Reply
My Dad used cheezwiz jars screwed into the shelves but that was over 40 years ago and I cannot remember whether there was issues with the rescrewing of the jars - it would be hard to imagine that there weren't issues. I just have mine sitting on the shelf in glass unfastened.
|
|
|
